these lamps are of the so-called 1206 size, measuring approximately 1.5 x 3.0 mm. JYC0118 page 1 of 5 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0902 part no. chip lens color material emitted color JYC0118 algainp yellow water clear
absolute maximum ratings at t a = 25 ?c parameter symbol rating units forward current i f 25 ma reverse voltage v r 5 v operating temperature t opr -40 to +85 ?c storage temperature t stg -40 to +90 ?c electrostatic discharge esd 2000 v power dissipation p d 60 mw peak forward current (duty 1/10 @ 1khz) i fp 60 ma soldering temperature t sol reflow soldering: 260? for 10 sec. hand soldering: 350? for 3 sec. electronic optical characteristics (t a = 25 ?c) parameter symbol min. typ. max. units condition luminous intensity i v 68 106 mcd i f = 20 ma viewing angle 2 1/2 60 deg peak wavelength p 591 nm dominant wavelength d 589 nm spectrum radiation bandwidth ? 15 nm forward voltage v f 1.7 2.0 2.4 v reverse current i r 10 a v r = 5 v JYC0118 page 2 of 5 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0902
typical electro-optical characteristics curves: JYC0118 page 3 of 5 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0902
reel dimensions: carrier tape dimensions: JYC0118 page 4 of 5 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0902
precautions for use 1. over-current prevention: a series resistor must be used for protection against over-current. since slight voltage shifts can cause large current changes and possibly damage the led. 2. storage: 2.1. store the leds in the sealed moisture proof bag until ready to use. 2.2. the storage conditions should be below 30? and 90% rh or less. 2.3. unused portions of leds may be stored in moisture proof packages for up to 1 year if kept under 30? and at no more than 60% rh. 2.4. if there is evidence of moisture absorption or if the leds have been stored for a long time, bake the leds at 60? ?5? for 24 hours prior to using. 3. reflow soldering conditions: 3.1. pb-free solder temperature profile (see figure): 3.2. reflow solder no more than two times and must include time interval for the board to cool. 3.3. when soldering, do not put stress on the leds during heating. 3.4. after soldering, do not warp the circuit board. 4. hand soldering: use a low wattage soldering iron (below 25 watts) with a tip temperature no more than 350? for 3 sec or less on one terminal. wait at least two seconds before soldering the next terminal to avoid overheating the led and damaging it. 5. avoid reworking a soldered led. it is best to simply replace it with a new part. JYC0118 page 5 of 5 * specifications subject to change without notice. dimensions are in mm ?.1 unless stated otherwise. idea, inc., 1 351 titan way, brea, ca 92821 ph: 714-525-3302, 800-led-idea; fax: 714-525-3304 0902
|
